Acumen DataBridge SDR2-CF Manual do Utilizador descarregar pdf (Página 9)

Click! 510

www.wavetronix.com

Click! 510 Bid Specication

1.0 General. This item shall govern the purchase and instal-

lation of a communication tester module (CTM) equivalent to

the Wavetronix Click!™ 510. Test results and other documen-

tation demonstrating performance and capabilities shall be

provided.

2.0 Product Description. The CTM shall be a communica-

tion tester module for use with serial devices, such as the

Wavetronix SmartSensor™. The CTM shall perform data link

latency tests and test paern tests; it shall also have a sensor

emulation mode. The CTM shall convert 2-wire half-duplex

RS-485 to half-duplex RS-232 and vice versa.

3.0 Physical. The CTM shall not exceed 0.29 lbs. (0.1 kg) in

weight.

The CTM shall not exceed 4.5 in. × 4 in. × 0.9 in. (11.4 cm x 10.2

cm x 2.3 cm) in its physical dimensions.

The CTM shall operate in the temperature range of -29°F to

165°F (-34°C to 74°C).

4.0 Mounting. The CTM shall mount to a DIN rail with hot-

swappable power and communication buses for quick installa-

tion and replacement.

5.0 Power. The CTM shall operate using less than 0.8 W of

average power at 10 VDC to 30 VDC.

6.0 Connections. The CTM shall include the following con-

nections for power and communication:

6.1 Power. The CTM shall include a 5-position connector,

with two contact points reserved for connecting power

through the bus.

The CTM shall supply voltage input monitoring with set-

table thresholds of 11.7 or 22.7 VDC.

6.2 Serial Ports. The CTM shall include the following

four independent physical serial ports:

● RS-232 front: DB-9 female DCE connector with DIP

switch override to select between programming and

run mode

● RS-485 top: 5-position connector for connecting from

T-bus

● RS-232 top: Pluggable screw terminal

● RS-485 top: Pluggable screw terminal and an RJ-11 jack

6.3 Digital Input Ports. The CTM shall include two multi-

function digital input ports with the following features:

● Low-level AC input monitoring via clamp-on split-core

current transformers with 1 W 120 VAC load threshold

suitable for monitoring incandescent or LED signal

indication status

● Contact closure input monitoring circuit that also

serves to monitor low-level DC logic with a threshold of

2.5 V

● DC voltage input monitoring with selectable thresholds

of 9, 11.7 and 23.4 VDC

● Maximum input event frequency of 250 Hz

6.4 Contact Closure Output Ports. The CTM shall feature

two solid state contact closure output ports with 250 Hz

of output signaling capability.

7.0 Communication. The CTM shall have the following com-

munication capabilities:

7.1 Serial Protocol Conversion. The CTM shall allow

communications with any serial device that has a serial

connection by converting 3-wire half-duplex RS-485 com-

munication to half-duplex RS-232 communication, and

vice versa.

8.0 Baud Rates. The CTM shall support a baud rate of 9600

bps.

9.0 Conguration Features. The CTM shall have a push-but-

ton on the faceplate of the unit that:

● Enters sensor emulation mode

● Enters test pattern mode

● Lets you manually select the baud rate

● Autobauds the CTM to match the baud rate of the attached

serial device

● Runs a data link latency test

● Resets to CTM factory defaults

The front of the CTM shall include a red power LED, as well as

green and yellow TX and RX LEDs that shall illuminate when

corresponding data is successfully transmied or received.

These LEDs, as well as the blue LED next to them, shall also

act as operation mode indicators for operation modes selected

with the push-buon.

The CTM shall include two banks of LEDs, one yellow and

one red, that display submenu selections and application

information.

10.0 Testing Features. The CTM shall feature a sensor emula-

tion mode where the device emulates a Wavetronix SmartSen-

sor V. In this mode, the CTM shall push or respond to queries

for SmartSensor V event data. It shall also be able to interact

with contact closure cards.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 ... 28 29

Comentários a estes Manuais

Sem comentários

Acumen DataBridge SDR2-CF Manual do Utilizador Página 9

Comentários a estes Manuais

Manuais e produtos relacionados com Redes Acumen DataBridge SDR2-CF